Macho313
MuscleChemistry Registered Member
Carrier Oil for Homebrew Steroid Injections
A good carrier oil for homebrew steroid injections should be thin,clean,sterile,painless,low in particulate matter,anallergic,and has good solubilizing ability.
EO = Ethyl Olate EO is a solvent, which dissolves the powder but its use is to thin the solution’s viscosity.It’s a thin and expensive oil, created from ethanol, and used as a rubber softener, solvent, and typically used by us as a base for steroid solutions. It provides smooth and painless injections, and will suspend compounds at much higher concentrations than just oil. (It will make 150mg/ml Prop completely painless…) " FOR MOST PEOPLE" And because it’s a solvent, it allows you to use less BB in your blends, however BA is still used to maintain sterility.
GSO = Grape seed oil.GSO is called the ‘carrier’.A much superior oil for injections, as opposed to cottonseed oil, but also has a shorter shelf life. It should be stored in a dark place, at room temp.
CSO=Cottonseed oil.It is very thick, and has trouble flowing through a small gauge needle. It’s just a byproduct of the food industry, so it is cheap and readily available.
Also some people use Wesson soybean oil,corn,peanut oil,sesame oil, soy oil, and safflower oil,MCT oil,olive oil, Mig840 etc.
There are some other carrier oils available like rice oil, apricot kernel, coconut, sweet almond oil, avocado, flaxseed, and watermelon seed oil.
What oil is the thinnest?
Castor – 297.0 thickest
Crambe – 53.6
High oleic safflower – 41.2
Peanut – 39.6
Sunflower – 37.1
Grapeseed – 37.0
Sesame – 35.3
Corn – 34.9
Cottonseed – 33.5
Soybean – 32.6
Safflower – 31.3
MCT 70/30 -27
Miglyol 840 -9-12
Sent from my LM-V405 using Tapatalk
A good carrier oil for homebrew steroid injections should be thin,clean,sterile,painless,low in particulate matter,anallergic,and has good solubilizing ability.
EO = Ethyl Olate EO is a solvent, which dissolves the powder but its use is to thin the solution’s viscosity.It’s a thin and expensive oil, created from ethanol, and used as a rubber softener, solvent, and typically used by us as a base for steroid solutions. It provides smooth and painless injections, and will suspend compounds at much higher concentrations than just oil. (It will make 150mg/ml Prop completely painless…) " FOR MOST PEOPLE" And because it’s a solvent, it allows you to use less BB in your blends, however BA is still used to maintain sterility.
GSO = Grape seed oil.GSO is called the ‘carrier’.A much superior oil for injections, as opposed to cottonseed oil, but also has a shorter shelf life. It should be stored in a dark place, at room temp.
CSO=Cottonseed oil.It is very thick, and has trouble flowing through a small gauge needle. It’s just a byproduct of the food industry, so it is cheap and readily available.
Also some people use Wesson soybean oil,corn,peanut oil,sesame oil, soy oil, and safflower oil,MCT oil,olive oil, Mig840 etc.
There are some other carrier oils available like rice oil, apricot kernel, coconut, sweet almond oil, avocado, flaxseed, and watermelon seed oil.
What oil is the thinnest?
Castor – 297.0 thickest
Crambe – 53.6
High oleic safflower – 41.2
Peanut – 39.6
Sunflower – 37.1
Grapeseed – 37.0
Sesame – 35.3
Corn – 34.9
Cottonseed – 33.5
Soybean – 32.6
Safflower – 31.3
MCT 70/30 -27
Miglyol 840 -9-12
Sent from my LM-V405 using Tapatalk
