Injectable Winstrol Recipe 50mg/ml

[KingLinc]

This is a recipe we use for 250ml

MCT oil:184.38 ml

Powder:12.5

BB:50ml-20%

BA:5ml- 2%

Here's the important part. You must cook this at 446F - 450F for 5.5-6 hours. Smaller batches may require less time. Let it sit overnight to make sure it doesn't crash. No sense in wasting a filter if you don't have to



king labs steroids anavar winstrol trenbolone clenbuterol testosterone

 

[Presser]

Good winny recipe! It always gave me a tough time so i would end up using oil instead

 

[Macho313]

This is a recipe we use for 250ml

MCT oil:184.38 ml

Powder:12.5

BB:50ml-20%

BA:5ml- 2%

Here's the important part. You must cook this at 446F - 450F for 5.5-6 hours. Smaller batches may require less time. Let it sit overnight to make sure it doesn't crash. No sense in wasting a filter if you don't have to



king labs steroids anavar winstrol trenbolone clenbuterol testosterone

Is this tried-and-true because I've never been able to get that much to hold, but overall never tried that much heat. Ive had problems getting it to hold with
25mg/ML
BA 2%
BB 18%
10%G
50/50 EO/MCT


Sent from my LM-V405 using Tapatalk

 

[KingLinc]

Is this tried-and-true because I've never been able to get that much to hold, but overall never tried that much heat. Ive had problems getting it to hold with
25mg/ML
BA 2%
BB 18%
10%G
50/50 EO/MCT


Sent from my LM-V405 using Tapatalk

This is a tried and true recipe that we use. We carry this in our product line. It took awhile to figure it out, but once we got the temperature down and cook time, we finally had success. You have to be patient with this one. Click on our banner King Labs for other blends we have

 

[KingLinc]

This is one of the hardest ones to deal with. Lots of patience is needed for Winny, but it can be done

 

[Presser]

This is one of the hardest ones to deal with. Lots of patience is needed for Winny, but it can be done

something im is short supply of half the time lol

 

[1_whocares]

I just saw this thread and wanted to add in. I as of tonight have two successful oil based winny brews.
First I have used micronized stanozolol powder so that might be part of it.
I use this ratio recipe
20% bb
1% ba, and this is important I have read that using 2% ba can cause holding issues after the brew cools so only 1%!
15% guiaicol, this is only slightly higher than your stated ratio so maybe with 1%ba I could do 10% guaiacol, idk.
Then for carrier is do
50/50 ethyl oleate and MCT.

Now I have only done a small 40ml brew and a second 80ml brew. So the smaller batch might have some influence, idk.

I am getting itchy to try brewing my "regular" stanozolol powder and see if it behaves differently than the micronized stuff.

And FYI I did my brew on a stove top cooking oil bath (think water bath but with cooking oil so I can go past boiling temp) I only go up to about 275f and it is only heated for about thirty minutes total. I start with carrier blend in one beaker and bb, guiaicol, ba and powder in a separate beaker. I heat until it is almost clear, usually around 250-275 f then I stir and that last bit goes clear. I then combine the two beakers. I keep stiring every couple of minutes. I only keep the heat on for about ten to 15 minutes after they are combined. Then I simply turn off the stove. I have a sterilized cooking sheet I place on top of the pan that still has the cooking oil and beaker in it. I place a towel on top of the sheet just as an added insulation. This part I think is very important, it is a SLOW cool down. I keep stiring every five minutes at least.
I let it sit overnight to make sure and yeah so far both batches held fine. Again the slow cool down is something I started recently with dhb cyp and I think it is important because it keeps the brew cooling at a consistent rate vs the top going cool first and getting ten degrees cooler than the bottom, or more.

Something about what I did there seems to produce a consistent product and quite frankly I don't think it is any harder to work with vs some other hormone. Keep in mind I am using micronized stanozolol powder.

 

[Presser]

I love oil based winstrol injections. I always thought micronized stanozolol powder was for making injectable winstrol anyhow. Though never tried with non-micronized

 

[Tailor]

This is a recipe we use for 250ml

MCT oil:184.38 ml

Powder:12.5

BB:50ml-20%

BA:5ml- 2%

Here's the important part. You must cook this at 446F - 450F for 5.5-6 hours. Smaller batches may require less time. Let it sit overnight to make sure it doesn't crash. No sense in wasting a filter if you don't have to



king labs steroids anavar winstrol trenbolone clenbuterol testosterone

Just to clarify. You mix powder with BA/BB and cook at 446F - 450F for 5.5-6 hours. Then cooling down and add MCT?

 

[SavageMcNasty]

Is there a special order to add the ingredients??

And so the only ingredients are powder, BA, BB & oil?

can I use grape seed oil??

 

[Macho313]

Is there a special order to add the ingredients??

And so the only ingredients are powder, BA, BB & oil?

can I use grape seed oil??

Yea but why would you want to with the quality and the price of MCT oil? Or even better 50/50 MCT/Mig840

Sent from my LM-V405 using Tapatalk

 

[DavidSchvim]

Winstrol (stanozolol) is very harsh on the lipids, unless you have an amazing lipid profile or aren’t sensitive to the adverse affects on cholesterol AAS can have I’d advise taking extreme precaution with regards to eating healthy, taking supplements

 

[DavidSchvim]

Winstrol (stanozolol) is very harsh on the lipids, unless you have an amazing lipid profile or aren’t sensitive to the adverse affects on cholesterol AAS can have I’d advise taking extreme precaution with regards to eating healthy, taking supplements. By the way I prefer use only Acquista Winstrol Online In Italia – Winstrol In Vendita Online - Comprare Winstrol Al Miglior Prezzo

Seems quality products.