MC IGF first run
- Thread starter formernpc
- Start date
formernpc
New member
How to Mix IGF-1 Long R3
Here are some instructions on how to mix or reconstitute IGF-1 Long R3. These instructions assume you have one vile of 1000 MCG of IGF-1 LR3 which is in the lyophilized form.
Most people use 1ml or 2mls of acetic acid (called AA from here on out) to mix their IGF-1 Long R3. Most IGF-1 kits come with 1 ml or cc of AA.
After removing the vacuum from the vile (do this by injecting a little air into the vile) of IGF-1 Long R3 slowly drizzle the AA into the vial.
Try not to let the stream of AA hit the powder directly. Try to let it run down the side of the glass into the powder.
After all the AA is in the vial of IGF-1 Long R3 gently swirl the vial. It is best to let it sit for a while in the fridge where the IGF-1 can continue to dissolve. Never shake your IGF-1 LR3; it is a very delicate peptide.
Mix/Reconstituting Instructions for IGF-1 Long R3
A 1 ml syringe is marked like this llll10llll20llll30llll40llll50llll60
A 1/2 ml syringe is like this llll5llll10llll15llll20llll25llll30
On a 1 ml syringe each line represents 2 units 2, 4, 6, 8, 10
On a 1/2 ml syringe each line is 1 unit 1, 2, 3, 4, 5, 6, 7, 8, 9, 10. This makes it easier to measure.
If you use 1 ml of AA, on a 1 ml insulin syringe, each line is 20 mcg. On a 1/2 ml syringe each line is 10 mcg.
If you use 2 ml of AA, on a 1 ml pin each line is 10 mcg, on a 1/2 ml each line is 5 mcg…the 5 line is 25 mcg, 10 line is 50 mcg
Your IGF-1 LR3 is stored in AA solution, nacl or bacteriostatic water is added to dilute at the time of injection. Draw twice as much nacl or bacteriostatic water as IGF-1. So if you draw IGF-1 LR3 to the ten line, draw nacl to the 30 line and you are ready to go
Here are some instructions on how to mix or reconstitute IGF-1 Long R3. These instructions assume you have one vile of 1000 MCG of IGF-1 LR3 which is in the lyophilized form.
Most people use 1ml or 2mls of acetic acid (called AA from here on out) to mix their IGF-1 Long R3. Most IGF-1 kits come with 1 ml or cc of AA.
After removing the vacuum from the vile (do this by injecting a little air into the vile) of IGF-1 Long R3 slowly drizzle the AA into the vial.
Try not to let the stream of AA hit the powder directly. Try to let it run down the side of the glass into the powder.
After all the AA is in the vial of IGF-1 Long R3 gently swirl the vial. It is best to let it sit for a while in the fridge where the IGF-1 can continue to dissolve. Never shake your IGF-1 LR3; it is a very delicate peptide.
Mix/Reconstituting Instructions for IGF-1 Long R3
A 1 ml syringe is marked like this llll10llll20llll30llll40llll50llll60
A 1/2 ml syringe is like this llll5llll10llll15llll20llll25llll30
On a 1 ml syringe each line represents 2 units 2, 4, 6, 8, 10
On a 1/2 ml syringe each line is 1 unit 1, 2, 3, 4, 5, 6, 7, 8, 9, 10. This makes it easier to measure.
If you use 1 ml of AA, on a 1 ml insulin syringe, each line is 20 mcg. On a 1/2 ml syringe each line is 10 mcg.
If you use 2 ml of AA, on a 1 ml pin each line is 10 mcg, on a 1/2 ml each line is 5 mcg…the 5 line is 25 mcg, 10 line is 50 mcg
Your IGF-1 LR3 is stored in AA solution, nacl or bacteriostatic water is added to dilute at the time of injection. Draw twice as much nacl or bacteriostatic water as IGF-1. So if you draw IGF-1 LR3 to the ten line, draw nacl to the 30 line and you are ready to go
formernpc
New member
SO you don't use the bacteriostatic water at all?
big in vegas
MuscleChemistry Registered Member
I don't, just go as is
big in vegas
MuscleChemistry Registered Member
It'll burn a little bit, but I'm not worried about that, I just don't to water it down at all. Just apply with 40mcg on each side and hit the gym, you may have just watered it down too much. I know when I apply it on my side delts I'll get a serious pump once I start doing side raises and I'll seriously have to quit from the pump. Then on bis, fuck, I'll get 2 sets of back in and my biceps will be so swollen I can't flex them so by the time my back workout is done and it's time to do bis, I have to fight through the pump to get a few sets in and my bis have never been as big as they are now and I'm probably doing less reps than ever before
formernpc
New member
will be trying it without
formernpc
New member
Thanks for the info...trying mine as is too
S
saudades
Guest
Same here.
Note that when you are using IGF-1, drinking the fruit juice isn't necessarily going to spike insulin because the IGF-1 is an antagonist to insulin although it works on the same cellular pathway. The carbs get shuttled into your muscles via the IGF-1 which is one of the reasons for the fantastic pumps you get while on it.
The difference is that the IGF-1 is already in the system, pumping cells with carbs, repairing and adding muscle cells while you're working out when taken pre-workout. I think you lose out on major fiber growth if you wait until after your workout to use IGF-1. I prefer to use it pre-workout, then fill up cells with nutrients after the workout using insulin.
formernpc
New member
Yeah u were, and I didnt even take you out to dinner first.... slut.
formernpc
New member
LMAO....you read what I wrote in one of your threads about the fat chick we had to pry off that toilet at the hospital? LMAO
yea bro I wrote back on it haha
big in vegas
MuscleChemistry Registered Member
Told you bro, shit is no joke, did it burn when you applied it?
big in vegas
MuscleChemistry Registered Member
Really starting to wonder about you lol
he's my boy I get to make jokes lol
big in vegas
MuscleChemistry Registered Member
Yea, I know you guys are boys, I'm just fucking with you....It just seems like everytime you guys post in the same thread some sick jokes come up lol
Similar threads
